P&E开发工具 Cosmic编译器 MetaGeek无线频谱分析 无线传感器网络

USB-ML-Universal
(又称U-MULTILINK)

USB Multilink Universal Debug Probe for ARM® devices and 8/16/32 bit devices(software sold separately)
Multilink Universal 多合一开发接口

特性:
  • 支持的芯片系列:Kinetis/S32, HCS08, RS08, HC(S)12(X), S12Z, ColdFire V1/+V1, ColdFire V2-4, Qorivva MPC5xxx, DSC, STMicroelectronics' SPC56, 和 ARM devices .
  • 从PC到Multilink的USB接口允许快速,方便的编程和调试--通过方便和兼容的USB接口。
  • USB供电 -无需单独的电源供应(目标烧写小于1mA)。
  • 目标电压:1.8V-5.25V
  • 目标频率:16KHz-50MHz (适用于HCS08,RS08,CFV1,S12Z,或HCS12X)
  • 自动频率检测+适应,用于HCS08设备。
  • 自动频率检测,用于HC(S)12(X)设备。
  • 对RS08设备在RESET line生成烧写电压
  • USB-ML-UNIVERSAL(Rev. E)连接RS08设备,需配套 RS08 adapter。
  • Supports JTAG daisy chaining of multiple ARM MCUs.
  • Pipelined programming algorithms for some Power Architecture families that dramatically increase programming speed.
  • ARM device support includes both the JTAG and SWD protocols

注:只包含硬件,配套软件需单独购买

USB-ML-Universal-FX
(又称U-MULTILINK-FX)

USB Multilink Universal FX High-Speed Debug Probe for ARM® devices and 8/16/32 bit devices(software sold separately)
Multilink Universal FX多合一开发接口

特性:
  • 支持的芯片系列:Kinetis/S32, HCS08, RS08, HC(S)12(X), S12Z, ColdFire V1/+V1, ColdFire V2-4, Qorivva MPC5xxx, DSC, STMicroelectronics' SPC56, MPC5xx/8xx, HC16, 683xx和 ARM devices .
  • 从PC到Multilink的USB接口允许快速,方便的编程和调试
  • USB供电 -无需单独的电源供应(目标烧写小于1mA).
  • 通信速度: 比其他P&EMultilink快10倍
  • 可为目标板供电
  • 目标电压:1.8V-5.25V
  • 目标频率:16KHz-50MHz (适用于HCS08,RS08,CFV1,S12Z,或HCS12X)
  • 额外的输入/输出保护
  • 自动频率检测+适应,用于HCS08的Trimming。
  • 自动频率检测,用于HC(S)12(X)设备。
  • 对RS08设备在RESET line生成烧写电压
  • I/O line clamping for added protection
  • Supports JTAG daisy chaining of multiple ARM MCUs.
  • Pipelined programming algorithms for some Power Architecture families that dramatically increase programming speed.
  • ARM device support includes both the JTAG and SWD protocols

注:只包含硬件,配套软件需单独购买

CYCLONE-LC-UNIV
(又称U-CYCLONE,cyclone universal)

Production Programmer and Debug Probe for ARM® devices and NXP 8/16/32-bit devices
烧写、调试和测试多合一开发工具用于NXP 8/16/32 和ARM Cortex 系列芯片

  • 支持的芯片系列: Kinetis/S32, HCS08, RS08, HC(S)12(X), S12Z, ColdFire V1/+V1, ColdFire V2-4, Qorivva MPC5xxx, DSC, HC08, MPC 5xx/8xx, STMicroelectronics' SPC56,ARM Cortex 系列,以及 STM8(with STM8 adapter) 和 Infineon(部分)
基础软件功能:
  • 脱机烧写 - 联机操作和脱机操作,两种操作方式
  • 基础自动控制 - 通过计算机进行 SDK, Console, and GUI 控制
  • 多种接口方式- USB,串口和以太网口三种计算机接口
  • LCD液晶触摸屏
  • 供电管理- 通过继电器控制Cyclone "power-in" a和 "power-out"口的供电。也可通过调试排线向目标板供电
  • 自动计数 和 共享序列号
  • Ethernet Based Debugging- Compatible with many development IDEs
  • 存储空间 - 16MB内存,最多存储8个程序
  • 编程控制接口 - 通过10-pin 接口控制编程启动,获取状态或显示结果
Cyclone 升级软件功能:

CYCLONE-FX-UNIV
(又称U-CYCLONE-FX,cyclone universal fx)

Advanced all-in-one program/debug/test interface for many ARM Cortex & NXP 8/16/32-bit devices.
烧写、调试和测试多合一开发工具用于NXP 8/16/32 和ARM Cortex 系列芯片。在烧写速度、加密和存储性能进一步提升。

  • 支持的芯片系列: Kinetis/S32, HCS08, RS08, HC(S)12(X), S12Z, ColdFire V1/+V1, ColdFire V2-4, Qorivva MPC5xxx, DSC, HC08, MPC 5xx/8xx, STMicroelectronics' SPC56,ARM Cortex 系列,以及STM8(with STM8 adapter)、Infineon(部分)和Renesas(with Renesas adapter
基础软件功能:
  • 脱机烧写 - 联机操作和脱机操作,两种操作方式
  • 基础自动控制 - 通过计算机进行 SDK, Console, and GUI 控制
  • 多种接口方式- USB,串口和以太网口三种计算机接口
  • LCD液晶触摸屏
  • 供电管理- 通过继电器控制Cyclone "power-in" a和 "power-out"口的供电。也可通过调试排线向目标板供电
  • 自动计数 和 共享序列号
  • Ethernet Based Debugging- Compatible with many development IDEs
  • 编程控制接口 - 通过10-pin 接口控制编程启动,获取状态或显示结果
Cyclone FX 特有高级功能:
  • 高速通讯 - 下载速率可达 75 Mbits/s
  • 存储空间 - 1G内存,可存储200+脱机文件
  • 目标电流和电压测量
  • ProCryption安全性 - RSA./AES 加密、限制编程次数或日期等
  • 高级自动控制 -包含 Gang Programming 和 Dynamic Data Programming等
  • 扩展内存 - SDHC接口支持SDHC卡,可满足更大存储需求

CYCLONE-LC-ARM
(又称ACP-CYCLONE)

Production Programmer and Debug Probe for ARM® devices
用于ARM Cortex™-M的通用在线烧写设备

基础软件功能:
  • 脱机烧写 - 联机操作和脱机操作,两种操作方式
  • 基础自动控制 - 通过计算机进行 SDK, Console, and GUI 控制
  • 多种接口方式- USB,串口和以太网口三种计算机接口
  • LCD液晶触摸屏
  • 供电管理- 通过继电器控制Cyclone "power-in" a和 "power-out"口的供电。也可通过调试排线向目标板供电
  • 自动计数 和 共享序列号
  • Ethernet Based Debugging- Compatible with many development IDEs
  • 存储空间 - 16MB内存,最多存储8个程序
  • 编程控制接口 - 通过10-pin 接口控制编程启动,获取状态或显示结果
Cyclone 升级软件功能:

USB-ML-ACP
USB Multilink Debug Probe for ARM® devices

特性:
  • 支持的芯片系列: ARM Cortex 系列
  • USB供电 -无需单独的电源供应(目标烧写小于1mA)。
  • 目标电压:1.8V-5.25V
  • Supports JTAG daisy chaining of multiple ARM MCUs.
  • ARM device support includes both the JTAG and SWD protocols

PROG-HL-ARM(former PROGACMP)
PROG for ARM® Cortex™ processors (Hardware License)

Kinetis ARM 烧写软件

通过P&E BDM USB Multilink Universal转换接口(P&E USB-ML-UNIVERSAL(FX),连接到目标板 mini-10或 mini-20针JTAG接口上),在线烧写内外闪存软件。
功能:

  • 烧写 Program
  • 校验 Verify
  • 检查 Blank check
  • 上载 Upload
  • 显示 Display
  • 擦写 Erase

LIC-CYC-CTRL-ADV
Cyclone LC Control Advanced Automation License

  • Simultaneously (Gang) Control of multiple Cyclones via the USB, Serial, or Ethernet connections
  • Add/Remove/Update many images in the Cyclone (Console, SDK, GUI)
  • Program (and Read) Dynamic Data in addition to fixed image data
  • Specify Overlay Program Data
  • Compare images against a SAP file

LIC-CYC-SDCARD
SD Card Port Activation License for Cyclone LC

  • 安装在Cyclone LC上激活SDHC端口
注:仅包含license,SDHC card 需单独购买
SDCARD
32 GB Encryped SDHC Flash Card for Cyclone
  • Easily be moved from Cyclone to Cyclone.
  • 32GB Encryptyed Cyclone SDHC Card is pre-formatted, tested, and certified to work with CYCLONE programmers.
注:需配套SDHC port License使用
LIC-CYC-PROCRYPTION
Cyclone LC Protected and Encrypted SAP Image Activation License
    It allows users to place protection on their programming images to restrict image use by date range or number of programs allowed. It also allows users to create RSA/AES encrypted programming images that use their own uniquely generated ImageKey. These images may only be used to program targets on Cyclones that are pre-configured with this unique ImageKey. This license keeps the user securely in control of both their IP and the programming process.
  • Restrict Image Use
  • Keep Programming Images Secure
  • Encryption is Easy To Implement and Manage

GDB Server Plug-In for Eclipse-based ARM IDEs
PEmicro plug-in for working with freely downloadable GDB Debugger

PEmicro's GDB Server Plug-In for Eclipse-based ARM IDEs is the piece which links the GDB debugger to PEmicro hardware, allowing debug and programming via USB, Serial, and Ethernet buses.

  • Real-Time Expression View
  • OS-Aware Feature Supports FreeRTOS
  • Multi-Core project debugging
  • Parallel debugging of multiple ARM devices
  • Preserve memory ranges across an erase
  • Trim Kinetis devices during programming
  • EEPROM partitioning capability during flash programming
  • SWD and JTAG : Both communications protocols are supported
  • JTAG daisy chain support
  • Attach to a running part during debug session
  • Attach to a running part during debug session
  • Semihosting : Simple way for target to send debug messages to the PC. To Eclipse or a Telnet client
  • Power Control : Many of PEmicro's debug interfaces can provide power to the target
  • Compatible PEmicro hardware interfaces include:

  • •Multilink ACP - development interface for ARM devices
    •Multilink Universal - all-in-one development interface and debug probe
    •Multilink Universal FX - Advanced high-speed all-in-one development interface and debug probe
    •Cyclone - series production programmers with stand-alone capability
    •Cyclone FX - series advanced high speed production programmers with stand-alone capability, speed, storage, security, and other enhancements
    •OpenSDA / Embedded OSJTAG- low-cost evaluation boards

JTAG_SWD Adpater

Cyclone MAX adapter module, provides mini-10 and mini-20 connectors for JTAG/SWD

Kinetis 适配器用于 mini-10 或mini-20针电缆连接到Kinetis 标准调试头 (如 P&E Cyclone MAX 烧写器20针标准连接头) 。它包含一个mini-20 和 mini-10针电缆

SWD(Serial Wire Debug)第2针代替JTAG 第5针。当MCU的针脚比较少时使用比较方便

Cyclone Automated Control Package(legacy)
Cyclone Automated Control Package with Dynamic Link Library (DLL).

P&E Cyclone PRO,P&E Cyclone MAX多机控制程序包,带有DLL动态联接库

Cyclone MAX (已停产)

P&E Multilink Cable硬件调试交互式转换接口和脱机烧写设备

Unit Library SDK for ARM® Cortex™-M processors

C/C++ and Delphi library modules which allow the creation of custom PC applications which use P&E hardware interfaces to control ARM® Cortex™-M processors via background debug mode

特性:

  • 通过Multilink Universal, Multilink Universal FX, CYCLONE-LC-UNIV, CYCLONE-FX-UNIV , CYCLONE-LC-ARM工作
  • 提供BDM交互界面
  • 包含C和Delphi两种语言模块
  • 具有C和Delphi原代码和相应的可执行演示程序
  • 支持多种编译环境
  • UNITACMP and UNITACMP_DIST: Microsoft Visual C++ 5.0 或更高版本, Delphi 2.0 或更高版本
    • 开发平台 Windows 32-bit,Windows 64-bit (XP, Vista, 7,8,10).
  • 适用生产线测试