USB-ML-Universal
USB Multilink Universal Debug Probe for ARM® devices and 8/16/32 bit devices(software sold separately)

• Support device：Kinetis/S32, HCS08, RS08, HC(S)12(X), S12Z, ColdFire V1/+V1, ColdFire V2-4, Qorivva MPC5xxx, DSC, STMicroelectronics' SPC56, and ARM devices .
• USB interface from PC to Multilink allows for fast, easy programming and debugging -- with the ease and compatibility of the USB interface.
• Draws power from USB interface-- no separate power supply required (draws less than 1mA from the target).
• Target Voltage:1.8V-5.25V
• Supports JTAG daisy chaining of multiple ARM MCUs.
• Pipelined programming algorithms for some Power Architecture families that dramatically increase programming speed.
• ARM device support includes both the JTAG and SWD protocols.
• Includes USB cable, Type A Male to Type B Male, 6-ft.
• Auto-frequency detection + trimming capabilities for HCS08 devices.
• Auto-frequency detection for HC(S)12(X) devices.
• Generates programming voltage on RESET line for RS08 devices.
• USB-ML-UNIVERSAL, Rev. E or later requires this RS08 adapter to allow the user to communicate with NXP's RS08 devices.

Note: Multilink debug probes do not include software, as there are myriad options regarding the device architecture and utility of software that the user might require.

USB-ML-Universal-FX
USB Multilink Universal FX High-Speed Debug Probe for ARM® devices and 8/16/32 bit devices(software sold separately)

• Support device： Kinetis/S32, HCS08, RS08, HC(S)12(X), S12Z, ColdFire V1/+V1, ColdFire V2-4, Qorivva MPC5xxx, DSC, STMicroelectronics' SPC56, MPC5xx/8xx, HC16, 683xx and ARM devices .
• High-speed USB interface from PC to Multilink allows for fast, easy programming and debugging -- with the ease and compatibility of the USB interface.
• Draws power from USB interface-- no separate power supply required (draws less than 1mA from the target).
• Can be used to power target MCU.
• Target Voltage:1.8V-5.25V
• Target Frequency: 16Khz-50Mhz (applies to HCS08, RS08, CFV1, S12Z, or HCS12X only)
• Supports JTAG daisy chaining of multiple ARM MCUs.
• Pipelined programming algorithms for some Power Architecture families that dramatically increase programming speed.
• I/O line clamping for added protection
• Auto-frequency detection + trimming capabilities for HCS08 devices.
• Auto-frequency detection for HC(S)12(X) devices.
• Generates programming voltage on RESET line for RS08 devices.
• ARM device support includes both the JTAG and SWD protocols

Note: Multilink debug probes do not include software, as there are myriad options regarding the device architecture and utility of software that the user might require.

• Support device： Kinetis/S32, HCS08, RS08, HC(S)12(X), S12Z, ColdFire V1/+V1, ColdFire V2-4, Qorivva MPC5xxx, DSC, HC08, MPC 5xx/8xx, STMicroelectronics' SPC56,ARM Cortex ,and STM8(with STM8 adapter),Infineon.

• Stand Alone Programming - Program targets with a PC or without a PC
• Powerful Automation Control - PC based SDK, Console, and GUI Control, Gang Programming, Dynamic Data Programming
• Multiple Communications Interfaces- USB 2.0, Ethernet, and Serial interfaces
• Touchscreen LCD Display - Easy to use touch screen interface with remote access
• Target Power Management- Ability to provide and switch power to a target
• Auto-Counting & Shared Serial Numbers - Programming can incorporate sophisticated serialization
• Ethernet Based Debugging- Compatible with many development IDEs
• On-Board Storage - Encrypted internal memory, 16MB, 8 images
• Programming Control Port -10-pin port can launch programming, get status/results

• ProCryption Security
  - RSA/AES Encryption (Unique ImageKeys Safeguard Valuable IP)
  - Programming count/Date limits, etc. (Exercise Control Over Remote Operations)

• Support device： Kinetis/S32, HCS08, RS08, HC(S)12(X), S12Z, ColdFire V1/+V1, ColdFire V2-4, Qorivva MPC5xxx, DSC, HC08, MPC 5xx/8xx, STMicroelectronics' SPC56,ARM Cortex , and STM8(with STM8 adapter),Infineon ,Renesas（with Renesas adapter）

• Stand Alone Programming - Program targets with a PC or without a PC
• Powerful Automation Control - PC based SDK, Console, and GUI Control, Gang Programming, Dynamic Data Programming
• Multiple Communications Interfaces- USB 2.0, Ethernet, and Serial interfaces
• Touchscreen LCD Display - Easy to use touch screen interface with remote access
• Target Power Management- Ability to provide and switch power to a target
• Auto-Counting & Shared Serial Numbers - Programming can incorporate sophisticated serialization
• Ethernet Based Debugging- Compatible with many development IDEs
• Programming Control Port -10-pin port can launch programming, get status/results

• High Speed Programming Target - Download rates reaching 75 Mbits/s
• Larger On-Board Storage - 1+ Gigabyte of encrypted internal memory stores 200+ programming images
• External SDHC Memory - External memory via SDHC Card Port
• Advanced Testing Feature - Run Tests Prior to Programming
• Target Current and Voltage Measurement
• ProCryption Security
  - RSA/AES Encryption (Unique ImageKeys Safeguard Valuable IP)
  - Programming count/Date limits, etc. (Exercise Control Over Remote Operations)

PROG-HL-CFV1(former PROGCFV1)
ColdFire V1 Flash Programmer Hardware License

P&E's PROGCFV1 Flash Programmer software allows you to program/reprogram external flash devices in-circuit, via one of P&E's hardware debug interfaces

Programmer features include:

• Program
• Verify
• Blank check
• Upload
• Display
• Erase

ColdFire V1 In-Circuit Debugger Hardware License

It allows users to place protection on their programming images to restrict image use by date range or number of programs allowed. It also allows users to create RSA/AES encrypted programming images that use their own uniquely generated ImageKey. These images may only be used to program targets on Cyclones that are pre-configured with this unique ImageKey. This license keeps the user securely in control of both their IP and the programming process.
• Restrict Image Use
• Encrypted (eSAP) Programming Images
• Encryption is Easy To Implement and Manage

This allows users to add expandable and easily swappable storage for their programming images. Adding one or more SD cards to your programming setup can give you added flexibility, while encryption helps keep your IP safe. An SD card can easily be moved from Cyclone to Cyclone. Our 32GB Encryptyed Cyclone SDHC Card is pre-formatted, tested, and certified to work with CYCLONE FX programmers. The SDHC port features are not available on Cyclone LC.

CPRO_PWRSUPPLY

Cyclone Power Supply Replacement Part

• Input - 100-240V, 50-60Hz, 0.48A
• Output - 5.9V, 3.0A, 17.7W, Center positive
• 58.25 inches (148cm) cable length
• Barrel connector - 5.5mm outer diameter, 2.5mm inner diameter
• 5 interchangeable international adapters

ColdFire V1 ASM Development Package Hardware License

Cyclone Automated Control Package(Legacy)
Cyclone Automated Control Package with Dynamic Link Library (DLL)

• Multiple Cyclone Control
• Error Detection
• Dynamic Data Programming
• Image Maintenance
• Download the Basic Edition Package at no cost!

• Please note that the Cyclone PRO is no longer available. It has been replaced by the CYCLONE-LC-UNIV and CYCLONE-FX-UNIV production programmers. These programmers support all of the devices supported by Cyclone PRO and are recommended for new programming projects.

• The USB-ML-12 (USB BDM Multilink) has been replaced with the Multilink Universal interface. Most software products will support the Multilink Universal transparently.Other compatible interfaces include the high-speed Multilink Universal FX, CYCLONE programmer, and CYCLONE FX programmer.

Unit Library SDK for ColdFire V1 and V2/V3/V4
C/C++ and Delphi library modules which allow the creation of custom PC applications which use P&E hardware interfaces to control ColdFire processors via background debug mode.

UNIT ColdFire Hardware Interface Library Routines (SDK)

The package includes both C/C++ and PASCAL modules.

The C and PASCAL modules come as sample source code。

The library is very useful for building your own production line testers.

The demo programs show you how to initialize the interface, program registers, download code and step through code.

Starting with these programs it is easy to customize them to your specific requirements.

Key Features：

• Works with ColdFire V1 architecture through P&E's USB-ML-Multilink Universal, Multilink Universal FX, CYCLONE-LC-UNIV , CYCLONE-FX-UNIV Hardware Interfaces
• Provides Interface to Background Debug Mode
• Included in the package are C/C++ and PASCAL modules
• Source and executables provided for both C and PASCAL demos
• Number of functions in the library - 23
• Compilers supported:

  • UNITCFZ and UNITCFZ_DIST：MicrosoftVisual C++ 5.0 or greater, Delphi 2.0 or greater for Development platform: Windows 32-bit, Windows 64-bit (XP, Vista, 7,8,10)

NOTE：Very useful for building production line tester