P&E Tools Cosmic Software MetaGeek WSN

USB-ML-Universal
USB Multilink Universal Debug Probe for ARM® devices and 8/16/32 bit devices(software sold separately)

FEATURES:
  • Support device:Kinetis/S32, HCS08, RS08, HC(S)12(X), S12Z, ColdFire V1/+V1, ColdFire V2-4, Qorivva MPC5xxx, DSC, STMicroelectronics' SPC56, and ARM devices .
  • USB interface from PC to Multilink allows for fast, easy programming and debugging -- with the ease and compatibility of the USB interface.
  • Draws power from USB interface-- no separate power supply required (draws less than 1mA from the target).
  • Target Voltage:1.8V-5.25V
  • Supports JTAG daisy chaining of multiple ARM MCUs.
  • Pipelined programming algorithms for some Power Architecture families that dramatically increase programming speed.
  • ARM device support includes both the JTAG and SWD protocols.
  • Includes USB cable, Type A Male to Type B Male, 6-ft.
  • Auto-frequency detection + trimming capabilities for HCS08 devices.
  • Auto-frequency detection for HC(S)12(X) devices.
  • Generates programming voltage on RESET line for RS08 devices.
  • USB-ML-UNIVERSAL, Rev. E or later requires this RS08 adapter to allow the user to communicate with NXP's RS08 devices.

Note: Multilink debug probes do not include software, as there are myriad options regarding the device architecture and utility of software that the user might require.

USB-ML-Universal-FX
USB Multilink Universal FX High-Speed Debug Probe for ARM® devices and 8/16/32 bit devices(software sold separately)

FEATURES:
  • Support device: Kinetis/S32, HCS08, RS08, HC(S)12(X), S12Z, ColdFire V1/+V1, ColdFire V2-4, Qorivva MPC5xxx, DSC, STMicroelectronics' SPC56, MPC5xx/8xx, HC16, 683xx and ARM devices .
  • High-speed USB interface from PC to Multilink allows for fast, easy programming and debugging -- with the ease and compatibility of the USB interface.
  • Draws power from USB interface-- no separate power supply required (draws less than 1mA from the target).
  • Can be used to power target MCU.
  • Target Voltage:1.8V-5.25V
  • Target Frequency: 16Khz-50Mhz (applies to HCS08, RS08, CFV1, S12Z, or HCS12X only)
  • Supports JTAG daisy chaining of multiple ARM MCUs.
  • Pipelined programming algorithms for some Power Architecture families that dramatically increase programming speed.
  • I/O line clamping for added protection
  • Auto-frequency detection + trimming capabilities for HCS08 devices.
  • Auto-frequency detection for HC(S)12(X) devices.
  • Generates programming voltage on RESET line for RS08 devices.
  • ARM device support includes both the JTAG and SWD protocols

Note: Multilink debug probes do not include software, as there are myriad options regarding the device architecture and utility of software that the user might require.

CYCLONE-LC-UNIV
Production Programmer and Debug Probe for ARM® devices and NXP 8/16/32-bit devices
  • Support device: Kinetis/S32, HCS08, RS08, HC(S)12(X), S12Z, ColdFire V1/+V1, ColdFire V2-4, Qorivva MPC5xxx, DSC, HC08, MPC 5xx/8xx, STMicroelectronics' SPC56,ARM Cortex ,and STM8(with STM8 adapter),Infineon.
Standard Cyclone Features:
  • Stand Alone Programming - Program targets with a PC or without a PC
  • Standard Automated Control - PC based SDK, Console, and GUI Control
  • Multiple Communications Interfaces- USB 2.0, Ethernet, and Serial interfaces
  • Touchscreen LCD Display - Easy to use touch screen interface with remote access
  • Target Power Management- Ability to provide and switch power to a target
  • Auto-Counting & Shared Serial Numbers - Programming can incorporate sophisticated serialization
  • Ethernet Based Debugging- Compatible with many development IDEs
  • On-Board Storage - Encrypted internal memory, 16MB, 8 images
  • Programming Control Port -10-pin port can launch programming, get status/results
Optional upgrades for Cyclone LC:
CYCLONE-FX-UNIV
Advanced all-in-one program/debug/test interface for many ARM Cortex & NXP 8/16/32-bit devices.
  • Support device: Kinetis/S32, HCS08, RS08, HC(S)12(X), S12Z, ColdFire V1/+V1, ColdFire V2-4, Qorivva MPC5xxx, DSC, HC08, MPC 5xx/8xx, STMicroelectronics' SPC56,ARM Cortex , and STM8(with STM8 adapter),Infineon ,Renesas(with Renesas adapter
Standard Cyclone Features:
  • Stand Alone Programming - Program targets with a PC or without a PC
  • Standard Automated Control - PC based SDK, Console, and GUI Control
  • Multiple Communications Interfaces- USB 2.0, Ethernet, and Serial interfaces
  • Touchscreen LCD Display - Easy to use touch screen interface with remote access
  • Target Power Management- Ability to provide and switch power to a target
  • Auto-Counting & Shared Serial Numbers - Programming can incorporate sophisticated serialization
  • Ethernet Based Debugging- Compatible with many development IDEs
  • Programming Control Port -10-pin port can launch programming, get status/results
Cyclone FX Advanced Features:
  • High Speed Programming Target - Download rates reaching 75 Mbits/s
  • Larger On-Board Storage - 1+ Gigabyte of encrypted internal memory stores 200+ programming images
  • Target Current and Voltage Measurement
  • ProCryption Security - RSA./AES encryption, programming count/Date limits, etc.
  • Advanced Automation Control - Advanced Feature Set includes Gang Programming, Dynamic Data Programming
  • External SDHC Memory - External memory via SDHC Card Port
CYCLONE-LC-ARM
Production Programmer and Debug Probe for ARM® devices Standard Cyclone Features:
  • Stand Alone Programming - Program targets with a PC or without a PC
  • Standard Automated Control - PC based SDK, Console, and GUI Control
  • Multiple Communications Interfaces- USB 2.0, Ethernet, and Serial interfaces
  • Touchscreen LCD Display - Easy to use touch screen interface with remote access
  • Target Power Management- Ability to provide and switch power to a target
  • Auto-Counting & Shared Serial Numbers - Programming can incorporate sophisticated serialization
  • Ethernet Based Debugging- Compatible with many development IDEs
  • On-Board Storage - Encrypted internal memory, 16MB, 8 images
  • Programming Control Port -10-pin port can launch programming, get status/results
Optional upgrades for Cyclone LC:

USB-ML-ACP
USB Multilink Debug Probe for ARM® devices

  • Supports devices:ARM Cortex-M devices only
  • USB interface from PC to Multilink allows for fast, easy programming and debugging -- with the ease and compatibility of the USB interface.
  • Draws power from USB interface-- no separate power supply required (draws less than 1mA from the target).
  • Target Voltage:1.8V-5.25V
  • Supports JTAG daisy chaining of multiple ARM MCUs.
  • ARM device support includes both the JTAG and SWD protocols.

PROG-HL-ARM(former PROGACMP)
PROG for ARM® Cortex™ processors (Hardware License)

PROG for ARM® Cortex™ Processors flash programmer software allows you to program/reprogram external flash devices from many ARM device manufacturers in-circuit, via one of PEmicro's compatible hardware debug interfaces. The programmer talks to the processor's Background Debug Mode through a compatible hardware interface (sold separately), which connects the parallel port or USB port of a PC to a mini-10 or mini-20 pin JTAG connector on the target system.

Feature:

  • Program
  • Verify
  • Blank check
  • Upload
  • Display
  • Erase

LIC-CYC-CTRL-ADV
Cyclone LC Control Advanced Automation License

  • Simultaneously (Gang) Control of multiple Cyclones via the USB, Serial, or Ethernet connections
  • Add/Remove/Update many images in the Cyclone (Console, SDK, GUI)
  • Program (and Read) Dynamic Data in addition to fixed image data
  • Specify Overlay Program Data
  • Compare images against a SAP file

LIC-CYC-SDCARD
SD Card Port Activation License for Cyclone LC

  • This license is installed onto a PEmicro's CYCLONE LC programmer to activate the SDHC Port
Note: This product includes the license only and does not contain an SDHC card. SDHC cards that are certified to work with PEmicro Cyclones are available separately.
SDCARD
32 GB Encryped SDHC Flash Card for Cyclone

    This allows users to add expandable and easily swappable storage for their programming images. Adding one or more SD cards to your programming setup can give you added flexibility, while encryption helps keep your IP safe. An SD card can easily be moved from Cyclone to Cyclone. Our 32GB Encryptyed Cyclone SDHC Card is pre-formatted, tested, and certified to work with CYCLONE FX programmers.

LIC-CYC-PROCRYPTION
Cyclone LC Protected and Encrypted SAP Image Activation License
    It allows users to place protection on their programming images to restrict image use by date range or number of programs allowed. It also allows users to create RSA/AES encrypted programming images that use their own uniquely generated ImageKey. These images may only be used to program targets on Cyclones that are pre-configured with this unique ImageKey. This license keeps the user securely in control of both their IP and the programming process.
  • Restrict Image Use
  • Keep Programming Images Secure
  • Encryption is Easy To Implement and Manage
注:需配套Cyclone-LC-UNIV使用

GDB Server Plug-In for Eclipse-based ARM IDEs
PEmicro plug-in for working with freely downloadable GDB Debugger

PEmicro's GDB Server Plug-In for Eclipse-based ARM IDEs is the piece which links the GDB debugger to PEmicro hardware, allowing debug and programming via USB, Serial, and Ethernet buses.

  • Real-Time Expression View
  • OS-Aware Feature Supports FreeRTOS
  • Multi-Core project debugging
  • Parallel debugging of multiple ARM devices
  • Preserve memory ranges across an erase
  • Trim Kinetis devices during programming
  • EEPROM partitioning capability during flash programming
  • SWD and JTAG : Both communications protocols are supported
  • JTAG daisy chain support
  • Attach to a running part during debug session
  • Attach to a running part during debug session
  • Semihosting : Simple way for target to send debug messages to the PC. To Eclipse or a Telnet client
  • Power Control : Many of PEmicro's debug interfaces can provide power to the target
  • Compatible PEmicro hardware interfaces include:

  • • Multilink ACP - development interface for ARM devices
    • Multilink Universal - all-in-one development interface and debug probe
    • Multilink Universal FX - Advanced high-speed all-in-one development interface and debug probe
    • Cyclone - series production programmers with stand-alone capability
    • Cyclone FX - series advanced high speed production programmers with stand-alone capability, speed, storage, security, and other enhancements
    • OpenSDA / Embedded OSJTAG- low-cost evaluation boards