• Support device： Kinetis/S32, HCS08, RS08, HC(S)12(X), S12Z, ColdFire V1/+V1, ColdFire V2-4, Qorivva MPC5xxx, DSC, HC08, MPC 5xx/8xx, STMicroelectronics' SPC56,ARM Cortex ,and STM8(with STM8 adapter),Infineon.

• Stand Alone Programming Images (SAP) Support - SAP Images are single file archives which contain all information, data, and algorithms necessary to program target devices with or without a PC
• Powerful Automation Control - PC based SDK, Console, and GUI Control, Gang Programming, Dynamic Data Programming
• Multiple Communications Interfaces- USB 2.0, Ethernet, and Serial interfaces
• Touchscreen LCD Display - Easy to use touch screen interface with remote access
• Target Power Management- Ability to provide and switch power to a target
• Auto-Counting & Shared Serial Numbers - Programming can incorporate sophisticated serialization
• Ethernet Based Debugging- Compatible with many development IDEs
• On-Board Storage - Encrypted internal memory, 16MB, 8 images
• Programming Control Port -10-pin port can launch programming, get status/results
• Cloud-Connected Programming Jobs (JOB) Support -Jobs are similar to images but use a connection to the Cloud to provide additional visibility, control, & logging via the free PEcloud service

• ProCryption Security
  - RSA/AES Encryption (Unique ImageKeys Safeguard Valuable IP)
  - Programming count/Date limits, etc. (Exercise Control Over Remote Operations)

• Support device： Kinetis/S32, HCS08, RS08, HC(S)12(X), S12Z, ColdFire V1/+V1, ColdFire V2-4, Qorivva MPC5xxx, DSC, HC08, MPC 5xx/8xx, STMicroelectronics' SPC56,ARM Cortex , and STM8(with STM8 adapter),Infineon ,Renesas（with Renesas adapter）

• Stand Alone Programming Images (SAP) Support - SAP Images are single file archives which contain all information, data, and algorithms necessary to program target devices with or without a PC
• Powerful Automation Control - PC based SDK, Console, and GUI Control, Gang Programming, Dynamic Data Programming
• Multiple Communications Interfaces- USB 2.0, Ethernet, and Serial interfaces
• Touchscreen LCD Display - Easy to use touch screen interface with remote access
• Target Power Management- Ability to provide and switch power to a target
• Auto-Counting & Shared Serial Numbers - Programming can incorporate sophisticated serialization
• Ethernet Based Debugging- Compatible with many development IDEs
• Programming Control Port -10-pin port can launch programming, get status/results
• Cloud-Connected Programming Jobs (JOB) Support -Jobs are similar to images but use a connection to the Cloud to provide additional visibility, control, & logging via the free PEcloud service

• High Speed Programming - Download rates reaching 75 Mbits/s
• Larger On-Board Storage - 1+ Gigabyte of encrypted internal memory stores 200+ programming Images/Jobs
• External SDHC Memory - External memory via SDHC Card Port
• Advanced Testing Feature - Run Tests Prior to Programming
• Target Current and Voltage Measurement
• ProCryption Security
  - RSA/AES Encryption (Unique ImageKeys Safeguard Valuable IP)
  - Programming count/Date limits, etc. (Exercise Control Over Remote Operations)

It allows users to place protection on their programming images to restrict image use by date range or number of programs allowed. It also allows users to create RSA/AES encrypted programming images that use their own uniquely generated ImageKey. These images may only be used to program targets on Cyclones that are pre-configured with this unique ImageKey. This license keeps the user securely in control of both their IP and the programming process.
• Restrict Image Use
• Encrypted (eSAP) Programming Images
• Encryption is Easy To Implement and Manage

This allows users to add expandable and easily swappable storage for their programming images. Adding one or more SD cards to your programming setup can give you added flexibility, while encryption helps keep your IP safe. An SD card can easily be moved from Cyclone to Cyclone. Our 32GB Encryptyed Cyclone SDHC Card is pre-formatted, tested, and certified to work with CYCLONE FX programmers. The SDHC port features are not available on Cyclone LC.

NOTE: This is a legacy product. The latest builds of Cyclone LC have an SD Card slot in the case but NO INTERNAL HARDWARE for this card. Cyclone LC users who wish to purchase this SDHC port activation license should be sure that their Cyclone meets these reuqirements:
Cyclone LC Universal: Rev. B, Date code 0620 or earlier
Cyclone LC ARM: Rev. D, Date code 0620 or earlier
The date code is located on the bottom right of the Cyclone's rear label.

Note: This product includes the license only and does not contain an SDHC card. SDHC cards that are certified to work with PEmicro Cyclones are available separately. PEmicro Cyclones support a minimum of 4GB SDHC card.

CPRO_PWRSUPPLY

Cyclone Power Supply Replacement Part

• Input - 100-240V, 50-60Hz, 0.48A
• Output - 5.9V, 3.0A, 17.7W, Center positive
• 58.25 inches (148cm) cable length
• Barrel connector - 5.5mm outer diameter, 2.5mm inner diameter
• 5 interchangeable international adapters

Cyclone Automated Control Package(Legacy)
Cyclone Automated Control Package with Dynamic Link Library (DLL)

• Multiple Cyclone Control
• Error Detection
• Dynamic Data Programming
• Image Maintenance
• Download the Basic Edition Package at no cost!

CAB_RIBBON_16-PIN

• 16-Pin, 9-Inch Ribbon Cable for 68HC08 (MON08) Connections

CYCLONE_PRO_POWER_CA
Replacement set of 3 power cables for Cyclone PRO.

• Qty. 2 - 2.5mm x 5.5mm to tinned lead
  
• Qty. 1 - 2.5mm x 5.5mm to 2.5mm x 5.5mm

USB-ML-MON08 （Discontinued）
MON08 Interface Pod (USB)

• The USB-ML-MON08 has been discontinued. The recommended replacement part is the CYCLONE-LC-UNIV automated programmer and debug interface.

• Please note that the Cyclone PRO is no longer available. It has been replaced by the CYCLONE-LC-UNIV and CYCLONE-FX-UNIV production programmers. These programmers support all of the devices supported by Cyclone PRO and are recommended for new programming projects.

CASM Command-Line Assembler
Command-Line Assembler

• Macro Support
• S19 objects
• Conditional Assembly
• Include Files
• Full listing control with cycle counter

CPROG08SZ
68HC08 Command-Line Programming Software

A command line version of the PROG08SZ software which programs EEPROM, EPROM, Flash, etc., on a 68HC08 based target.

• BM Blank check module
• BR Blank check range
• EB Erase byte range
• EW Erase word range
• EM Erase module
• PB Program bytes
• PW Program words
• PM Program module
• CM Choose module .08P file
• VM Verify module
• VR Verify range
• VC Verify module CRC-8
• UM Upload module

ICS08_ALL
Complete P&E ICS08 Software

• WinIDEIntegrated Development Environment（IDE）
• ICD08SZ Real Time In-Circuit Debugger
• PROG08SZMON08 Flash/EEPROM Programmer
• ICS08full Chip Simulator
• The ICS08 and ICD08SZ feature assembly source-level debugging using the P&E MAP file format as well as C source-level debugging using ELF/DWARF v2.0 or ImageCraft v1.1 debug file format.

WINIDE
68HC08 Windows Integrated Development Environment

P&E's WinIDE08Z allows you to run external programs - including assemblers, C-compilers, debuggers, and flash programmers - in one environment, with a single hotkey for each. WinIDE08Z comes installed with P&E's CASM assembler

Editor features include:

• Fully Reconfigurable
• Allows execution of external programs
• On-screen help

Assembler features include:

• Macro support
• S19, HEX, IEEE695 objects
• Conditional assembly
• Include files
• Full listing control with cycle counter